Tools You Need to Install a New Bath Tub
Tools You Need to Install a New Bath Tub
Blog Article
We've stumbled upon this article relating to How to Install a Bathtub Yourself below on the internet and figured it made perfect sense to talk about it with you over here.
Setting up a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is likewise a moderately hard job. If the old tub is conveniently available, the project can relocate quickly; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job as well as are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed task, it is far better to consider utilizing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bath tub in your restroom if you have currently acquired a brand-new tub as well as do not require to transform the arrangement of your previous supply of water pipelines.
Your devices and material checklist must consist of the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its final setting.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be rather bothersome as a result of the restricted gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, place the bath tub in the required placement. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and also examine the overflow outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub ought to wait till the tub has been made use of a minimum of once as this will certainly settle it into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washers are in area in between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to penetrate the wall between the bath as well as the tiling, causing difficulties with moisture and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealer can fracture rather very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that blog entry about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the internet. So long as you liked our blog post kindly do not forget to pass it around. Thanks for going through it.
Book 24/7
Report this page